(Tenda)F3-How to setup PPPOE Mode
(Tenda)F3-How to setup PPPOE Mode
Note: If you have no idea about what is the connection type of your network, please contact the ISP (Internet Service Provider) to confirm it.
Step 1: Connect the broadband line to the WAN port of router, and then connect your computer to LAN1/LAN2/LAN3 port by a cable. Physical connection as bellow:
F3-How%20to%20setup%20PPPOE%20Mode.files/image001.png)
Step 3: Setup the router
1. Open a browser then type “192.168.0.1” into the Address Bar, press Enter, and you can see the quickest setting page.
F3-How%20to%20setup%20PPPOE%20Mode.files/image002.png)
2. Select “PPPOE” option. Type the username and password from your ISP, and tap “OK”.
F3-How%20to%20setup%20PPPOE%20Mode.files/image003.png)
Note: If you do not know or forget your user name or password, please call your ISP to check it.
3. Setup the name and password of your WI-FI signal in “Wireless Settings”. Set them as you want, then tap “OK” to save this setting.
F3-How%20to%20setup%20PPPOE%20Mode.files/image004.png)
Note: If you do not want to setup password for your Wi-Fi, keep the “WiFi password” bar empty.
4. Then the page will pop into homepage of your F3. You can see your Wi-Fi status in “Status”. If the information is shown as below, you can surf the internet now.
F3-How%20to%20setup%20PPPOE%20Mode.files/image005.png)
NOTE: When the Connection Status is “connecting”, please try the steps as below.
1. Tap “Administration”à“WAN Parameters”à “Clone MAC”.
Some ISPs will bind your broadband account info and a specified MAC address of your computer together. If you can only access the Internet with a specified computer without a Router, you can try cloning MAC address for normal Internet access. By default, it clones the factory MAC address (the MAC address of the router). If you want to clone the MAC address of the current attached computer, select “manual” and input the MAC address of the current attached computer on its right. Then tap “OK” to save this setting.
F3-How%20to%20setup%20PPPOE%20Mode.files/image006.png)
2. Tap “Administration”à“WAN Parameters”à “WAN speed”.
In WAN Parameters, pelase choose WAN Speed in the drop-menu. Then click OK to save the settings.
By default, the WAN rate is set as “Auto”. Generally, it is not advisable to change the default value. When the cable length between your Router and the remote device (modem, Router, etc.) is relatively long, you can set WAN rate to 10M FDX or 10MHDX to enhance transmission rate.
F3-How%20to%20setup%20PPPOE%20Mode.files/image007.png)
Related Articles
How to configure Cudy Wi-Fi router into Wireless Extender Mode?
How to configure Cudy Wi-Fi router into Wireless Extender Mode? Common network topology: Step 1: Open a web browser and go to http://cudy.net or http://192.168.10.1. Use "admin" as password to log in. For details, please refer to How to log into the ...Setup Scan to Folder - Sharp
Setup Scan to Folder - Sharp Create user -> scan password scan Create Shared Folder on PC and give user scan full access Open Eset Antivirus -> Setup -> Networks Connections Make sure the connected network connection is trusted Test if you can ping ...ZTE LTE ROUTER SETUP APN
Manual Setup 1. Open your preferred browser (Safari, Chrome, Edge, Firefox) and enter 192.168.0.1 in the address bar. 2. You will be prompted for a password which can be found written on the sticker underneath your router. 3. Once logged in, you will ...TendaF3- Change WiFi Password
(Tenda)F3-How to change your SSID and password Step 1: Login the homepage. 1. Open a browser then type “192.168.0.1” into the Address Bar, press Enter. Then enter the password of this page. Tap “Login”. Note: The default password is shown on the ...GXP21XX End User Guide
Grandstream Networks, Inc. GXP2130/GXP2140/GXP2160/GXP2170/GXP2135 Enterprise IP Phones User Guide